RX6110SA (Real time clock module)
Power Switching and Low current consumption SPI & I2C-Bus

RX6110SARX6110SA

  • ・Built in frequency adjusted 32.768 kHz crystal unit.
  • ・Interface Type
    :SPI-Bus & I2C-Bus
  • ・Operating voltage range
    :1.6V to 5.5V
  • ・Wide Timekeeper voltage range
    : 1.1V to 5.5V
  • ・Low backup current
    : 130 nA / 3V(Typ.)
  • ・Built-in RAM
    : Built-in 128 bit(8 bit x 16)RAM
  • ・Auto power switching functions
    : When VDD deteriorates than 1.6V, internal source is switched to VBAT.
  • ・The various functions include full calendar, alarm, timer.
  • arrowLinux® driver available.

DataSheet pdf(458KB) /  ApplicationNotepdf(845KB)

Block diagram

Terminal connection External dimensions

Overview

  • Interface type.
    • SPI-Bus and I2C-Bus interface.
    • By a terminal, a switchover of the interface is possible.
  • Built-in auto power switching function
    • When VDD deteriorates, internal source is switched to VBAT.
  • Frequency output function
    • Output frequency can be selected as 32.768kHz, 1024Hz, 1Hz.
  • Timer function
    • ・Timer function can be set up between 1/4096 second and 65535 hours.
    • ・It is recorded automatic to TF-bit at the time of event occurrence,and possible to output with /IRQ1 or /IRQ2 pin.
  • Alarm function
    • ・Alarm function can be set to day of week, day, hour, and minute.
    • ・It is recorded automatic to AF-bit at the time of event occurrence,
      and possible to output with /IRQ1 pin output.
  • Built-in RAM
    • 128 bit (8 bit x 16 word)

Pin Function

Signal Name Input/
Output
Function
SPISEL Input The interface select pin.
SPI is chosen at a "H" level (VIO voltage) / I2C is chosen at a "L" level (GND voltage).
CE/FOE Input SPI: Should be held high to allow access to the CPU. Incorporates a pull-down resistor.
I2C: It is an input pin for controlling the DO/FOUT output. When the frequency output from a DO/FOUT pin does not need, CE/FOE pin must be connected to GND.
CLK/SCL Input This is a shift clock input pin for serial data transmission.
DI/SDA Input/ Output SPI: This is the data input pin for serial data transfer.
I2C: This is the data input/output pin for serial data transfer.
DO/FOUT Output SPI: This is the data output pin for serial data transfer.
I2C: This is the C-MOS output pin with output control provided via the CE/FOE pin. (frequency selection: 32.768 kHz / 1024 Hz / 1Hz / Hi-z)
/ IRQ1 Output This pin outputs interrupt signals ("L" level) for alarm, timer, time update, and FOUT. This is an N-ch open-drain output. This pin can output even a backup mode.
/ IRQ2 Output This pin outputs interrupt signals ("L" level) for timer and FOUT. This is an C-MOS output. This pin becomes Hi-z in less than VDD=1.6V.
VDD - This is a power-supply pin. It can impress the voltage unlike VIO.
VIO - This pin is a power supply for input and the output and input / output pins.Connected to a positive power supply.
VBAT - Connect a secondary battery or capacitor for backup power supply.If a backup power supply is not present, this pin connect to VDD.
GND - Connected to a ground.

Terminal connection / External dimensions

(Unit:mm)

Terminal connection External dimensions

※The metal case inside of the molding compound may be exposed on the top or bottom of this product.
This purely cosmetic and does not have any effect on quality, reliability or electrical specs.

Specifications (characteristics)

*Refer to application manual for details.

■Recommended Operating Conditions

Item Symbol Conditions Min. Typ. Max. Unit
Power voltage VDD - 1.6 3.0 5.5 V
Clock voltage VCLK - 1.1 3.0 5.5 V
Operating temperature TOPR - -40 +25 +85 °C

■Frequency characteristics

Item Symbol Conditions Rating Unit
Frequency   tolerance Δ f/f Ta=+25°C
VDD=3.0V
B:5±23 *
×10-6
Oscillation
start-up time
tSTA Ta=+25°C
VDD=1.6V
1 Max. s

*1) Equivalent to 1 minute of monthly deviation (excluding offset.)

■Current consumption characteristics *Ta=-40°C to+85°C

Item Symbo Conditions Min. Typ. Max. Unit
Current Consumption lBAK VBAT=3.0V
Input pins are "L" ,VDD = 0 V DO/FOUT=OFF, fCLK = 0 Hz, /IRQ1,2 = OFF, TSEL2=”1” It include an OFF leak current of SW between the power supply (VBAT-VDD)
- 130 250 nA
I32K VDD=3.0V
fCLK = 0 Hz,SPISEL=VIO,
/IRQ1,2 = OFF, CE/FOE = VIO,
DO/FOUT : 32.768 kHz ON ,
CL = 0 pF
- 1.5 2.1 μA