RX6110SA A (Real Time Clock Module Customized Product)
Power Switching and Low current consumption SPI & I2C-Bus

RX6110SA ARX6110SA A

  • Built in frequency adjusted 32.768 kHz crystal unit.
  • Frequency tolerance
    5±11.5x10-6 (Equivalent to 30 seconds of monthly deviation/ Customized product
  • Interface Type
    SPI-Bus & I2C-Bus
  • Operating voltage range
    1.6V to 5.5V
  • The wide voltage for time keeping
     1.1V to 5.5V
  • Low backup current
     170 nA / 3V(Typ.)
  • Built-in RAM
     Built-in 128 bit(8 bit × 16)RAM
  • Auto power switching functions
     When VDD deteriorates than 1.6V, internal source is switched to VBAT.
  • The various functions include full calendar, alarm, timer.
  • Epson prepared Linux driver for development
  • http://www5.epsondevice.com/en/information/support/linux_rtc/
    The registered trademark Linux® is used pursuant to a sublicense from LMI(Linux Mark Institute)
  • The I2C-Bus is a trademark of NXP Semiconductors

Block diagram

Terminal connection External dimensions

Overview

  • Interface type.
    • SPI-Bus and I2C-Bus interface.
    • By a terminal, a switchover of the interface is possible.
  • Built-in auto power switching function
    • To efficiently charge from VDD to backup battery (Secondary battery, Large capacitor)
      connected to VBAT is possible.
      Detects VDD voltage drop(VDET-) and automatically switches to the backup battery.
  • Frequency output function
    • Output frequency can be selected as 32.768kHz, 1024Hz, 1Hz.
  • Timer function
    • Timer function can be set up between 1/4096 second and 65535 hours.
  • Timer source clock are 1hour, 1min, 64Hz, 4096Hz
    • It is recorded automatic to TF-bit at the time of event occurrence, and possible to output with /IRQ1 or /IRQ2 pin.
  • Alarm function
    • Alarm function can be set to day of week, day, hour, and minute.
    • It is recorded automatic to AF-bit at the time of event occurrence,
      and possible to output with /IRQ1 pin output.
  • Built-in RAM
    • 128 bit (8 bit x 16, SRAM)

Specifications (characteristics)

*Refer to application manual for details.

Recommended Operating Conditions

Item Symbol Conditions Min. Typ. Max. Unit
Power voltage VDD - 1.6 3.0 5.5 V
Clock voltage VCLK - 1.1 3.0 5.5 V
Operating temperature TOPR - -40 +25 +85 °C

Frequency characteristics

Item Symbol Conditions Rating Unit
Frequency   tolerance Δ f/f Ta=+25°C
VDD=3.0V
A:5± 11.5*1)
×10-6
Oscillation
start-up time
tSTA Ta=+25°C
VDD=1.6V
1 Max. s

*1) Equivalent to 30 seconds of monthly deviation (excluding offset.)/ Customized product

Current consumption characteristics

*Ta=-40°C to+85°C

Item Symbo Conditions Min. Typ. Max. Unit
Current Consumption lBAK VBAT=3.0V
Input pins are "L" ,VDD = 0 V DO/FOUT=OFF,
fCLK = 0 Hz, /IRQ1,2 = OFF, TSEL2="1"
It include an OFF leak current of
SW between the power supply (VBAT-VDD)
- 170 320 nA
I32K VDD=3.0V
fCLK = 0 Hz,SPISEL=VIO,
/IRQ1,2 = OFF, CE/FOE = VIO,
DO/FOUT : 32.768 kHz ON ,
CL = 0 pF
- 1.5 2.1 µA

name

Pin Function

Signal Name Input/
Output
Function
SPISEL Input The interface select pin.
SPI is chosen at a "H" level (VIO voltage) / I2C is chosen at a "L" level (GND voltage).
CE/FOE Input SPI: Should be held high to allow access to the CPU. Incorporates a pull-down resistor.
I2C: It is an input pin for controlling the DO/FOUT output.
When the frequency output from a DO/FOUT pin does not need, CE/FOE pin must be connected to GND.
CLK/SCL Input This is a shift clock input pin for serial data transmission.
DI/SDA Input/ Output SPI: This is the data input pin for serial data transfer.
I2C: This is the data input/output pin for serial data transfer.
DO/FOUT Output SPI: This is the data output pin for serial data transfer.
I2C: This is the C-MOS output pin with output control provided via the CE/FOE pin. (frequency selection: 32.768 kHz / 1024 Hz / 1Hz / Hi-z)
/ IRQ1 Output This pin outputs interrupt signals ("L" level) for alarm, timer, time update, and FOUT.
This is an N-ch open-drain output. This pin can output even a backup mode.
/ IRQ2 Output This pin outputs interrupt signals ("L" level) for timer and FOUT. This is an C-MOS output.
This pin becomes Hi-z in less than VDD=1.6V.
VDD - This is a power-supply pin. It can impress the voltage unlike VIO.
VIO - This pin is a power supply for input and the output and input / output pins.Connected to a positive power supply.
VBAT - Connect a secondary battery or capacitor for backup power supply.
If a backup power supply is not present, this pin connect to VDD.
GND - Connected to a ground.

Terminal connection / External dimensions

Terminal connection External dimensions

(Unit:mm)

The metal case inside of the molding compound may be exposed on the top or bottom of this product.
This purely cosmetic and does not have any effect on quality, reliability or electrical specs.

Footprint (Recommended)

footprint

(Unit: mm)

To maintain stable operation, provide a 0.1uF by-pass capacitor
at a location as near as possible to the power source terminal of the crystal product (between Vcc - GND).

Page Top